<
<
These days, clip on flip up sunglasses are the in thing because not only are they very stylish, but they are also very handy to use as compared to a real pair of sunglasses. The great thing about this type of thing is that one does not necessarily need to buy one because it is so easy to make one right at home. So if one would want to try making one, then here are some instructions how.
Now the very first thing to do would be to get a pair of old and cheap sunglasses and start taking the arms out with a screwdriver. By doing this, he will be left with just the two lenses of the pair of glasses. Make sure to be very careful with this part because the glasses will become quite fragile.
The next step is to grab hold of a paper clip that is quite hard so that the clip will be steady. After this, one should now get some pliers and make it very straight. Always do this very slowly because it is quite possible that the wire will break if handled too fast.
When the wire has been straightened, then one should get a pair of tough scissors and try to cut the wire into two. Then the next thing to do would be to get a wire and try to put it into the hole where the arms of the glasses was taken out. He must also do this for the other hole.
After the wires have been slotted in, then the next thing that one should do would be to actually tie the wires to the holes. The thing about this is that it is very hard to tie the wires by hand because these things are really tough. So in order to make a tight knot, one should use pliers to be able to tie the wire so that it will not be loose later on.
After that, one should now bring the two ends of the wire to the top middle of the glasses. Now one should make sure that the wire is attached to the frame so that the wire will not be seen by the wearer. From there, one should make a knot using the two ends of the paper clip so that it will stay steady.
When a small knot has already been formed, then the next part would be to curve the wire a little bit. This little curve will be the one that will be attached to the very center of the glasses. When everything fits well, then it may now be worn outside.
So as one can see, it is actually very easy to make a pair of clip on flip up sunglasses. The great thing about this device is that it is very practical because it is easier to use than a normal pair of sunglasses. It is also much cheaper to make one at home because the ones outside are very expensive.
Now the very first thing to do would be to get a pair of old and cheap sunglasses and start taking the arms out with a screwdriver. By doing this, he will be left with just the two lenses of the pair of glasses. Make sure to be very careful with this part because the glasses will become quite fragile.
The next step is to grab hold of a paper clip that is quite hard so that the clip will be steady. After this, one should now get some pliers and make it very straight. Always do this very slowly because it is quite possible that the wire will break if handled too fast.
When the wire has been straightened, then one should get a pair of tough scissors and try to cut the wire into two. Then the next thing to do would be to get a wire and try to put it into the hole where the arms of the glasses was taken out. He must also do this for the other hole.
After the wires have been slotted in, then the next thing that one should do would be to actually tie the wires to the holes. The thing about this is that it is very hard to tie the wires by hand because these things are really tough. So in order to make a tight knot, one should use pliers to be able to tie the wire so that it will not be loose later on.
After that, one should now bring the two ends of the wire to the top middle of the glasses. Now one should make sure that the wire is attached to the frame so that the wire will not be seen by the wearer. From there, one should make a knot using the two ends of the paper clip so that it will stay steady.
When a small knot has already been formed, then the next part would be to curve the wire a little bit. This little curve will be the one that will be attached to the very center of the glasses. When everything fits well, then it may now be worn outside.
So as one can see, it is actually very easy to make a pair of clip on flip up sunglasses. The great thing about this device is that it is very practical because it is easier to use than a normal pair of sunglasses. It is also much cheaper to make one at home because the ones outside are very expensive.
<
;
<
;
Posts
No comments:
Post a Comment